The DuKane underwater acoustic beacon is designed to generate a kHz signal that radiates underwater to a distance of about 2 miles. Works to a depth of . Find great deals for Dukane Underwater Acoustic Beacon DK Battery. Shop with confidence on eBay!. Dukane DK Pdf User Manuals. View online or download Dukane DK Technical Manual.
|Published (Last):||9 September 2006|
|PDF File Size:||2.87 Mb|
|ePub File Size:||15.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Honeycomb structure, tarpaulin fabrics, clothing, parachutes, cargo, etc. The signal iscoupled to a piezo-ceramic transducer ring.
Surface to 20, feet meters Pulse Length Remove the old O-ring from the cover. Insure that proper protection for the beacon is provided i.
Physical Characteristics Watertight aluminum case 1. Any situation that could possibly crush or penetrate the case dkk120 the beacon should be avoided. Position mounting kit carefully to avoid interference with other structures.
The DK Series beacon is a battery-operated underwater acoustic pulse generator that is activated when the water switch is immersed in either fresh or salt water. The DK Series beacon is a battery-operated underwater acoustic pulse generator that isactivated when dukaje water switch is immersed ineither fresh or salt water. When the beacon is returned under warranty, ship to: Return Authorization Number See 9. The beacon complies with the preceding operational performance standards after being subjected to environmental tests specified in FAA TSO-C Remove the old battery.
Seacom Service Department A.
What’s missing? Tell us about it.
When long term storage of the beacon is required, the beacon should be stored in the original shipping container or equivalent. Contact Dukane Corporation, Seacom Division atfor replacement battery kits. The aft mid-section of the aircraft is normally the most desirable location for the beacon, but consideration must be given to environmental conditions outlined in Section 2. Screw securing plate in place with the set of furnished screws and washers.
Any dk1120 that could possibly crush orpenetrate the case of the beacon should beavoided. Tell us what’s missing.
Initially beacons must betested at every installation or beacon change. Shipping and billing addresses. The beacon should be stored without battery.
Safety Data Sheets & Service Bulletins – Dukane Seacom – A HEICO Company
Sustained pressure up to psi. The beacon should be mounted horizontallywith the switch end forward, if possible. Tell us about it. In the case of a failure which is determinedto be within the Warranty terms Section VII ,the beacon will be replaced by Dukane Corporation at the sole discretion of Dukane Corporation. After the four 0. This mount is used for applications where space limitations do not permit the use of the simpler N30A26 Series cradle mount. Make sure that the beacon case and water switch are free of grease or film.
Dukane DK Specifications |
Ship beacons to Dukane Corporation per paragraph 9. Or point us to the URL where the manual is located.
Thebeacon should be mounted horizontally with theswitch end forward, if possible. Where a choice exists, horizontal mounting with switch forward is best. Use a high impedance voltmeter input impedance of 10 M ohms not required when usingTS or TS Test Set to perform the following procedure: See Sections V and VI. The signal is coupled to a piezo-ceramic transducer ring.
When horizontal mounting is used,position beacon with switch end forward.
Dukane DK120 Manuals
Rated output over 80 percent of sphere Size The beacon must not be disassembled in any way. Dukaane the four 0. Be sure that all four studs protrude approximately the same amount to insure that the strap seats properly around the beacon. The proper mounting location should also provide for clearance for removing the beacon from its mounting hardware.
The beacon is operable at the given minimum acceptable voltage. The beacon is a battery-powered device and installed shelf life is affected by higher than normal temperatures. For other applications of these products please contact the factory for information regarding the warranty, installation, maintenance, and use. It can be detected at a range of to yards to meters. The beacon Figure Make sure that the beacon case and water switch, are free of grease or film.
Lay out four holes as shown in Figure Dj120 the threads, O-ring groove in the bodyand the threads on the cover by wiping themthoroughly with solvent. The water switch is part of a triggeringcircuit, which when actuated will initiate normalpulsing of the beacon circuit. The beacon is mounted to a flight recorder or the airframe by means of a mounting kit See Section II.
This warranty does not cover: